960E-2K

> Specifications  > Features  > Charts  > Standard Equipment

> Optional Equipment   > Need a Quote?

  Print Brochure (3,248 Kb)

Click for Larger Image

< Page 1 2 >  
 
Engine   
Make and model*    Komatsu SSDA18V170 
Fuel    Diesel 
Number of cylinders    18 
Operating cycle    4 cycle 
Gross horsepower** @ 1900 rpm  3,500 HP  2610 kW 
Net flywheel power*** @ 1900 rpm  3,346 HP  2495 kW 
Weight (wet)  25,897 lb  11750 kg 
Weight (dry)  24,795 lb  11250 kg 
* Optional Tier 4 emission compliant engine for North American market. Non-emissionized engine for markets outside of North America.     
** Gross horsepower is the output of the engine as installed in this machine, at governed rpm and with engine manufacturer’s approved fuel setting. Accessory losses included are water pump, fuel pump and oil pump.     
***Net flywheel power is the rated power at the engine flywheel minus the average accessory losses. Accessories include fan and charging alternator. Rating(s) represent net engine performance in accordance with SAE J1349 conditions.     
 
Electric Drive   
AC/DC CURRENT     
Drive System*.    Komatsu AC Drive 
Alternator    Siemens 
Dual Fan Main Blower:     
Alternator Flow  9,380 cfm  266 m³/min 
Wheel Motor Flow  14,800 cfm  419 m³/min 
Control    IGBT AC Torque Control System 
Ratio    38.12 
Speed (maximum)  40 mph  64.5 km/h 
* Drive system performance depends upon gross vehicle weight, haul road grade, haul road length, rolling resistance and other parameters. Komatsu must analyze each job condition to assure acceptable application.     
 
Tires and Rims   
Rock service, tubeless, radial tires     
Standard tire*    56/80 R63 
Flange mount rim:     
Rim assembly  41'' x 63'' x 5.5''  1041 mm x 1600 mm x 140 mm 
Rims rated at 758 kPa / 110 psi cold inflation pressure.     
Typical tire weight  65,154 lb  29553 kg 
* Tires should meet application requirements for tkph/tmph, tread, compound, inflation pressure, ply rating or equivalent, etc.     
 
Body   
All-welded steel flat floor body with horizontal bolsters and full canopy. Rubber mounts on frame are standard. Eyebrow, body up sling, extended canopy and pivot exhaust heating are optional. 
Floor sheet
200,000 psi / 1379 mPa tensile strength steel / Outer 
0.63''  16 mm 
Floor sheet
200,000 psi / 1379 mPa tensile strength steel / Center 
0.75''  19 mm 
Front sheet
200,000 psi / 1379 mPa tensile strength steel / Outer 
0.39'  10 mm 
Front sheet
200,000 psi / 1379 mPa tensile strength steel / Center 
0.47''  12 mm 
Side sheet
200,000 psi / 1379 mPa tensile strength steel 
0.39'  10 mm 
Canopy sheet
100,000 psi / 690 mPa tensile strength steel 
0.24''  6 mm 
Capacity struck  195 yd³  149 m³ 
SAE heaped 2:1  280 yd³  214 m³ 
Standard Komatsu body weight  90,000 lb  40823 kg 
 
Cab   
Advanced Operator Environment with integral 4-post ROPS/FOPS Level 2 cab (ISO 3449), adjustable air suspension seat w/lumbar support and arm rests, full-size passenger seat, maximum R-value insulation, tilt and telescoping steering column, electric windshield wipers w/washer, tinted glass, power windows, Payload Meter III, 61,000 Btu/hr heater and defroster, 19,900 Btu/hr air conditioning (HFC - 134A refrigerant). 
 
Frame   
Advanced technology, full butt-welded box sectional ladder-type frame with integral ROPS supports, integral front bumper, rear tubular cross members, steel castings at all critical stress transition zones, rugged continuous horsecollar. 
Plate material
tensile strength steel 
70,000 psi  482.6 mPa 
Casting material
tensile strength steel 
90,000 psi  620.5 mPa 
Rail width  12''  305 mm 
Rail depth (minimum)  34''  864 mm 
Top and bottom plate thickness  1.77''  45 mm 
Side plate thickness / Rear  0.98''  25 mm 
Side plate thickness / Front  1.26''  32 mm 
Drive axle mounting    Pin and spherical bushing 
Drive axle alignment    Swing link between frame and axle 
 
Braking System   
Service brakes: Oil-cooled, hydraulic actuated, multiple disc brakes at each wheel 
Traction system    Wheel Spin-Slide Control 
Max. service apply pressure  2750 psi  18960 kPa 
Total friction area per brake  16,078 in²  103729 cm² 
Secondary brakes    Automatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements. 
Wheel brake locks    Switch activated 
Parking brakes    Multiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on +-15% grade at maximum gross vehicle weight 
Electric dynamic retarder  6,196 HP  4620 kW 
Continuously rated high-density blown grids w/retard capacity at low speeds and retard in reverse.     
 
Suspension   
Variable rate hydro-pneumatic with integral rebound control 
Max. front stroke  12.92''  328 mm 
Max. rear stroke  9.40''  239 mm 
Max. rear axle oscillation    ±6.5º 
 
Cooling System   
L&M radiator assembly, split-flow, with deaerator-type top tank. 
Radiator frontal area  75.5 ft²  7.02 m² 
 
Service Capacities   
Cooling System  190 U.S. gal  719 L 
Crankcase  90 U.S. gal  341 L 
Hydraulic system  350 U.S. gal  1325 L 
Motor gear box (each)  37 U.S. gal  140 L 
Fuel tank  1400 U.S. gal  5300 L 
 
Hydraulic System   
Steering    Accumulator assisted with twin double acting cylinders provide constant rate steering. Secondary steering automatically supplied by accumulator. 
Turning circle diameter (SAE)  105'  32 m 
Reservoir  250 U.S. gal  947 L 
Filtration    In-line replaceable elements 
Suction    Single, full flow, 100 mesh 
Hoist and steering    Dual, in-line, high pressure 
Brake component cabinet    Above deck, easily accessible with diagnostic test connections 
Hoist    Two 3-stage dual-acting outboard cylinders, internal cushion valve, over-center dampening 
Hoist times:     
Power-up loaded    24 sec 
Power-down    14 sec 
Float-down empty    24 sec 
Pumps    Two pumps, single package, in-line 
Hoist and brake cooling    Tandem gear pump with output of 931 lpm / 246 gpm at 1900 rpm and 18960 kPa / 2750 psi 
Steering and brake    Pressure-compensating piston pump with output of 246 lpm / 65 gpm at 1900 rpm and 20685 kPa / 3,000 psi 
System relief pressures:     
Hoist and brake cooling  2,500 psi  17237 kPa 
Steering and brake  3,000 psi  20685 kPa 
Ports available for powering disabled truck and for system diagnostics.     
 
Electrical System   
4 x 8D 1450 CCA, 12 volt, in series/parallel, bumper-mounted with disconnect switch. 
Alternator    24 volt, 250 amp 
Lighting    24 volt 
Cranking motors    Two/24 volt 
 
Weight Distribution   
Empty vehicle weight:     
Front Axle Distribution / 49.5%  272,250 lbs  123490 kg 
Rear Axle Distribution / 50.5%  277,750 lbs  125985 kg 
Total EVW  550,000 lbs  249475 kg 
Gross vehicle weight:     
Front Axle Distribution / 33%  419,100 lbs  190104 kg 
Rear Axle Distribution / 67%  850,900 lbs  385968 kg 
Nominal GVW  1,270,000 lbs  576072 kg 
Nominal Payload  720,000 lbs (360 short tons)  326585 kg (327 metric tons ) 
Nominal payload is defined by Komatsu America Corp’s payload policy documentation. In general, the nominal payload must be adjusted for the specific vehicle configuration and site application.     
The figures above are provided for basic product description purposes.     
Please contact your Komatsu distributor for specific application requirements.     

< Page 1 2 >